一、概述Outline

QJ(D/S)DX型精小型氣動橡膠蝶閥是由氣動活塞式執行機構和襯里蝶閥組成，屬旋轉類控制閥。
該產品以壓縮空氣為動力源，接受控制儀表的4-20mA信號(或開關信號)，通過電-氣閥門定位器(或電磁閥)實現對閥門的連續調節(或位式控制)。
橡膠襯里蝶閥是一種閥體內腔襯有橡膠的防腐蝕蝶閥。控制腐蝕性流體不與閥體接觸，閥體可用普通鑄鐵或碳鋼，由此降低蝶閥的成本。襯里材料有各種橡膠可供選擇，還可更換。
該產品結構簡單，輸出力矩大，性能優越。蝶閥通常適用于控制密封要求比較高的腐蝕性流體。

QJ (D / S) DX-type fine small pneumatic rubber valve is pneumatic piston actuator and lining butterfly valve, is a rotary type control valve.
The product is compressed air as power source, to accept 4-20mA control signal meter (or switch signals), through the electric - gas valve locator (or solenoid valve) to achieve the continuous adjustment of the valve (or bit control).
Rubber lined butterfly valve is a body cavity lined with rubber anti-corrosion butterfly. Corrosion control and body fluid does not contact the valve body can be an ordinary cast iron or steel, thus reducing the cost of butterfly. There are a variety of rubber lining materials available, can be replaced.
The product is simple, the output torque, and superior performance. Control valve normally sealing requirements for high corrosive fluids.

二、主要技術參數Main technical parameters

公稱通徑mm	50	65	80	100	125	150	200	250	300	350	400	450	500	600
額定流量系數Kv	71	100	198	340	500	770	1360	2130	3060	4160	5450	6900	8500	12000
公稱壓力Mpa	0.6、1.0、1.6
連接方式 Connection	對夾式(管道法蘭標準：JB/T79-94、GB9113-2000 Wafer (pipe flange standard: JB/T79-94, GB9113-2000)
介質溫度℃ Temperature	-20~+180
輸入信號Input signal	0.4~0.6Mpa/調節型0.02-0.1Mpa(4-20mA) 0.4 ~ 0.6Mpa / Regulated 0.02-0.1Mpa (4-20mA)
額定行程Rated travel	調節型：70°  切斷型：90° Modulating: 70 ° cut-off: 90 °
環境溫度℃ Temperature	-40~+150、-40~+180
氣源接口 Air Connection	1/8 ″G 、    NAMUR1/4″G
固有流量特性 Inherent flow characteristic	近似等百分比Approximately equal percentage
泄露等級 Leakage level	ANSIB16.104 IV級、VI(軟密封) ANSIB16.104 IV level, VI (soft seal)

注：允許壓差可參照QJD(S)DR型氣動蝶閥該指標

Note: Allow pressure to refer QJD (S) DR pneumatic valve of the indicators

三、性能指標Performance indicators

項目Item			帶定位器指標值Index value with locator
基本誤差Basic error%			±2.5
回差Hysteresis%			2.5
死區Dead%			1.0
始終點偏差 Always point deviation%	氣開 Open air	始點 Starting point 終點End	±2.5
			±2.5
	氣關 Gas off	始點 Starting point 終點End	±2.5
			±2.5

四、執行機構轉扭及動作時間Twist and turn actuators operating time

執行機構型號AGT		63×90	75×90	83×90	92×90	110×90	118×90	127×90	160×90	210×90	254×90	255×90
扭矩N.m	400Kpa	23.2	40.0	56.0	77.6	112.8	168.0	220.0	440.0	948.0	1740.0	2172.0
	500Kpa	29.0	50.0	70.0	97.0	141.0	210.0	275.0	550.0	1185.0	2715.5	2715.0
動作時間(S)		0.241	0.333	0.429	0.444	0.461	0.60	0.857	1.62	3.33	6.00	7.50

 注：1、雙作用執行機構在75%負載情況下的動作時間    2、縮短動作時間可允許非標配置

Note: 1, double-acting actuators at 75% load case, the action time of 2 to shorten the operating time to allow non-standard configuration

五、可配附件Available Accessories

調節型：電-氣閥門定位器，空氣過濾減壓器，手輪機構等。
切斷型：定位開關，空氣過濾減壓器，電磁閥，手輪機構等。

Adjustment type: electric - gas valve positioner, air filter regulator, hand wheel institutions.
Cut-off: position switch, air filter regulator, solenoid valve, hand wheel institutions.

六、主要零件材質與內腔襯材料Material of main parts and cavity lining material

零件名稱Part Name	材料Material
閥體Body	各種橡膠、聚四氟 A variety of rubber, PTFE
蝶板Disc	灰鑄鐵、球墨鑄鋼、鑄鋼、不銹鋼及特殊材料 Gray cast iron, ductile cast steel, cast steel, stainless steel and special materials
密封圈Ring	球墨鑄鋼、鑄鋼、合金鋼、不銹鋼 Ductile cast steel, cast steel, alloy steel, stainless steel
閥桿Stem	2Cr13、不銹鋼 2Cr13, Stainless Steel
填料Filler	O型圈、柔性石墨 O-ring, flexible graphite

1.閥體內腔襯材料Body cavity lining materials

材料品種 Variety of materials	氯丁橡膠 Neoprene	丁腈橡膠NBR	乙丙橡膠EPDM	硅橡膠Silicone rubber	氟橡膠Viton
代號Code	X或J	X 或JA	XB或 JB	XD或 JD	XE 或JE
耐*高溫度 Maximum temperature resistance	82℃	93℃	150℃	250℃	204℃
耐*低溫度 Minimum temperature resistance	-40℃	-40℃	-40℃	-70℃	-23℃
適用工作溫度 Suitable temperature	≤65℃	≤80℃	≤120℃	≤200℃	≤180℃

七、外形尺寸Dimensions

標準值Standard value					參考值Reference
DN	L	D	D1	Z-d	H	H0	A	B	W(kg)
50	43	99	125	4-18	170	130	45	120	24.7
65	46	118	145	4-18	170	145	45	120	25.6
80	46	132	160	4-18/8-18	320	186	160	240	27
100	52	156	180	8-18	320	192	310	100	30.8
125	56	184	210	8-18	345	200	370	118	37.6
150	56	211	240	8-22	385	230	370	118	43.2
200	60	266	295	8-22/12-22	471	297	450	143	100.8
250	68	319	350	12-22	533	327	450	143	118.5
300	78	370	400	12-22	606	364	535	178	159
350	78	429	460	16-22	694	404	535	178	180.7
400	102	480	515	16-26	757	444	630	248	216.8
450	114	530	565	20-26	814	472	1162	232	266.1
500	127	582	620	20-26	902	522	1162	232	325
600	154	682	725	20-30	1048	590	1380	318	355
700	165	794	840	24-30	1277	810	1380	318	585
800	190	901	950	24-33	1385	844	1860	350	798
900	203	1001	1050	28-33	1490	890	1860	350	906
1000	216	1112	1160	28-36	1620	950	1860	350	1055